Home > Products > Gas mask > Full Face Gas Mask > MF18C poison gas protection mask

MF18C poison gas protection mask

Basic Info

Model No.: MF18C

Additional Info

Packaging: inner packing:250*170*170mm Gross weight:1kg 20piece Carton box external packing:870*430*370mm Gross weight:22kg Carton box


Place of Origin: Shanxi, China (Mainland)

Product Description

1. Product Information

 The type MF18C canister Mask is a novel design Gas Mask, whose canister is connected directly to the face piece. When the air is a contaminated NBC agent, the Gas mask provides effective Protection to the wearers respiratory organs, eyes and facial skin. The gas mask is designed for the military, police and civil defense and can also be used in industry, agriculture, storehouses, scientific research work, etc.

Coated with anti-mist and abrasionproof inside and outside of the shock resistance PC lense surface, the antimist propeltties wiu be much more better. The mask has the facepiece with doubu inturned lip seal which is suitable for different face.

   ♥"Xinhua Brand"gas masks are produced in accordance with GB2890-1995«General technical specifications for filter type gas mask»,its protective objects and gas life depend on the selected canister. 

 2.MF18C type canister mask Specifications:

  Cyanogen chloride life Oil mist penetration coefficient Inhalation resistance Exhalation resistance Visual field Weight


gas mask


(30l/min,1.5mg/l  and 80%~80% RH cnditions)

≤0.005%(30l/min) ≤186Paa(30l/min) ≤100Pa(30l/min)


binocular visual field>55%



 4.Usage maintenance and maintain

4.1.The selection of gas mask

 (1)checking the position between glasses and eyes, if the position of our eyes is 10mm higher than the horizontal center line, that proves the size is correct. And if it is higher than this, that means the size is small, and on the contrary that indicate the size is big.

(2)Pressing the connector of the canister tightly, and taking a breath, if the mask clings face without any air leakage that means a right selection.

 4.2.The procedure of wearing gas mask

 (1)   adjusting the position of fillets

 (2)   opening them and putting the mask on and then tightening the fillets to finish wearing Attention:

 (3) fillets can not be curl or be pressed inside the mask

 (4)  the stretching forces on each fillet should be equal

 (5) screwing the canister tightly up the connector in order to prevent air leakage

 (6)  considering both comfortable and air tightness while tightening the fillets

 (7)  after a long time wearing, there would have accumulation of sweat, especially in summer days, on this occasion, bowing down and taking a deep breath, the sweat would release form the exhaust clack.

 4.3.Pick gas mask off

Grasping the phone and lifting it up ahead to pick the gas mask off bottom-up.

 4.4The maintenance and storage of gas mask

(1)     wiping the sweat and dirty things on both side of the mask after using keeping the glasses and exhale vale clean especially

(2)     in case of having dirty on the exhaust clack, opening the voice meter and pick out the combination of exhaust clack and phone film to make a clean, and then setting them up as original, tightening the cover

(3)     stalling the mask in a shady dry place with supporter inside, the same time keeping them away from the organic solvent such as gasoline etc, in order to prevent the distortion of mask

(4)     taking the canister off when it would not be used for a long time, and putting the cover, because the canister would low the capacity of adsorption under a wet condition.

(5)     in case of water penetration into the canister, replacing a new one at once.



Product Categories : Gas mask > Full Face Gas Mask

Email to this supplier
  • *Subject:
  • *Messages:
    Your message must be between 20-8000 characters
Communicate with Supplier?Supplier
wangfengyin Mr. wangfengyin
What can I do for you?
Contact Supplier